Uncoiler-manufacture,factory,supplier from China

1. Hydraulic core expansion 2. Electric discharge3. Bearing capacity 8 tons 4. Distribution box (frequency conversion control, slow start and slow stop) 5. Hydraulic 2.2KW setRoll inner diameter: φ508mm; inner diameter expansion and contraction range ф450-500;Maximum outer diameter of material roll: φ1250mm;

1. Hydraulic core expansion with press arm2. Distribution box (frequency conversion control, slow start and slow stop)3. Electric discharging4. Hydraulic 3KW set5.

Hydraulic core expansion   2. Electric discharge   3. Bearing capacity 10 tons  4. Distribution box (frequency conversion control, slow start and slow stop)  5. Hydraulic 3KW set

Equipment composition: decoiler → forming host → online punching and cutting → splicing table1. Uncoiler: vertical manual tensioning (bearing 3 tons)2.

primary component1. Uncoiler, hydraulic core, distribution container (frequency conversion manage sluggish upward push and sluggish stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling computing device with eleven leveling rollers (3 top and four lower), with a energy of 5.5KW.3.

main component1. Uncoiler, coil width: 850mm, coil inner diameter: 530mm, maximum coil outer diameter: 1500mm, hydraulic station 3KW set, load-bearing 8 tons2. Leveling and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), 13-roller leveling, 45 on the leveling shaft, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2-section high-speed platform, front and back screw width adjustment, feeding speed controlled by frequency conversion4.

main component1. Uncoiler, bearing capacity 2 tons2. Leveling machine3. Roll forming part, main shaft φ40mm, surface hard chromium plating, 6 rows of forming rollers, reinforced ribs, hydraulic punching, 1 set of plane straightening after forming, roll material: GCr15, 1 set of hydraulic system 3.0KW4. One unloading rack5.

main component1. Uncoiler, load-bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 1 roller leveling (3 upper and 4 lower), power 4.0KW3. All-in-one punching and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), hydraulic 3KW set, load-bearing 8 tons2. Leveling and cutting machine, 13-roller leveling, hydraulic system 11KW, 2 sets of electric valves, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2 high-speed platforms, forward and reverse screw width adjustment, frequency conversion control4. Punch machine, 3 motors, distribution box, mold pneumatic conversion single and double row, oil cylinder heavy engineering oil cylinder5.

main component1. Uncoiler, hydraulic core, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling machine - 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

1. Uncoiler, manual core starting, load bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 4.0KW3. Integrated punching and cutting machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

main component1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

This cable tray roll forming machine is mainly composed of an uncoiler, a leveling machine, a punching machine, and a roll forming machine. It can produce solid bottom cable trays, tray hole cable trays, ladder cable trays, cable tray covers, etc. We There are professional design engineers who can provide plans and drawings according to needs.Details descriptionThis uncoiler is a hydraulic core expander with an electric unwinding capacity of 10 tons.

main component1 、Uncoiler machine hydraulic loading, passive feeding, load bearing 5 tons, with brake function2、 leveling and punching integrated machine ，leveling up 3 down 4,1 set of hydraulic system, hydraulic cut-off, hydraulic punching3、 roller forming part ，spindle surface plating hard chromium, forming after the plane straight 1 set, roll material: GCr12, lengthened feed guide position4 、Tracking cut ，hydraulic cut (plug), servo tracking, a set of hydraulic system5、 Passive unloading rack 2 sets                      &

The total length of this production line is 42 meters. It can produce metal sheets of 220-1450mm with a thickness of 0.5-3.0mm. It is equipped with two sets of punching dies with large and small gaps. The production speed is 12 meters per minute. The entire assembly line is leveled by an uncoiler. It consists of cutting part-conveying platform-punching machine-conveying platform-roller forming host-receiving frame.The equipment is equipped with a decoiler with a load capacity of 10 tons, hydraulic core expansion, and electric feeding, which is more convenient to operate.

The total length of this cable tray production line is 33 meters. The width of the metal strips used for production is 160~550mm, the thickness is 0.5~1.5mm, and the production speed is 12m/min. The control panel controls the production. It has a high degree of automation, is stable and reliable, and saves costs. , Achieve truly zero laborCable tray forming machine process flowHydraulic uncoiler→Leveling machine→Punching and cutting machine→Conveyor platform→Roll forming part→Unloading rack 

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control 4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller fo

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller for

Serial numbermain componentConfiguration1Uncoiler1. Hydraulic core expansion 4. Distribution box (frequency conversion control, slow start and slow stop) 2. Electric discharge 5. Hydraulic 3KW set3.

This production line covers an area of 17 meters long and 25 meters wide.

main component1、Open rolling machine ，hydraulic core, bearing 5 tons, distribution box (frequency conversion control slow up slow stop), hydraulic 3KW set 2 ， 13 roller leveling, hydraulic system 111 KW 2 group electric valves, 7.5KW motor , Hydraulic cutting, tray punching (optional) 3, section A high speed platform ， 2 high speed platform, width adjustment of positive and reverse wire rod, frequency conversion control, 4, punching machine，mold pneumatic transformation single and double row, oil cylinder heavy engineering cylinder, typing (trademark) (optional) 5, section

main component1 、feeding rack ， hydraulic feeding rack2 、leveling ， unpowered 5 roller leveling (top 2 bottom 3)3 、roller forming ， spindle surface plating hard chromium, forming roll 16 rows, the main machine is divided into 2 sections, forming plane straight 1 set, roll material: GCR 154、 tracking cut ， hydraulic cut, servo tracking, hydraulic system a set of 4KWTechnical Parametersorder numberprojectunitnumerical value1Material widthMmInplate width 600mm2Material thicknessMm0.5～1.2mm3material type galvanized steel strip   4Equipment running speedm/min1-15 m/min5powerKw&n

a. Form: Roller type active leveling machineb. Functional and structural features: leveling steel belt. It consists of pinch rollers and leveling rollers. The pinch rollers can be adjusted individually. The upper leveling roller adopts an integral structure and has two adjustment points at the front and rear, which can form a certain tilt angle to improve the leveling quality. The upper pinch feeding and leveling rollers are raised and lowered using 8.8-grade high-quality ball screws.

The diameter of the spindle of this forming host is 65mm, and it has 25 rows of forming rollers to ensure that the finished product comes out with a straight outline. The surface of the forming rollers is hard chromium plated with a thickness of 0.05mm, which ensures the smoothness of the rollers and the products are not easy to scratch. It is equipped with an extended feeding guide rail , a set of plane straightening after forming, the pressure roller is made of GR12 material, which has stronger hardness, longer service life, and has the function of reinforcing ribs on the bottom and sides!